 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Silicon Hall ICs 6.6 Application Notes: Differential Hall IC TLE 4921-3U Applications * * * * Detection of rotational speed of ferromagnetic gear wheels Detection of rotational position Detection of rotational speed of magnetic encoder wheels Generation of trigger signals Main Features * * * * * * * * * Evaluation of very small magnetic field differences Large airgap in dynamic mode Low cut-off frequency Fully temperature compensated Clean, fast, bounce-free switching Overvoltage and reverse polarity protection Guarded against RF interference Wide temperature range Open-collector output General Description The TLE 4921-3U has a combination of two Hall cells, a differential amplifier and evaluating circuitry, all on a single chip. Evaluating field difference instead of absolute field strength means that disruptive effects, like temperature drifts, manufacturing tolerances and magnetic environment are minimized. Further reduction in interference is obtained by the dynamic evaluation of the difference signal using a highpass filter with an external capacitor. The IC is designed for use under aggressive conditions found in automotive applications. A small permanent biasing magnet is required for sensing ferromagnetic gear wheels of various shapes. Correct switching for even the smallest field differences between tooth and gap is guaranteed. The typical lower switching frequency is about 10 Hz for a 470 nF filter capacitor. The TLE 4921-3U is offered in a 1 mm thick ultraflat package with four leads (P-SSO-4-1). Data Book 31 2000-07-01 Silicon Hall ICs Design and Function of the Chip When the Hall IC is exposed to a constant magnetic field of either polarity, the two Hall elements will produce the same output signal. The difference is zero, regardless of the absolute field strength. However, if there is a field gradient from one Hall element to the other, because one element faces a field concentrating tooth and the other one a gap of the toothed wheel, then a difference signal is generated. This signal is amplified on the chip. In reality the difference exhibits a small offset which is corrected by the integrated control mechanism. The dynamic differential principle allows a high sensitivity in combination with large airgaps between the sensor surface and the gear wheel. A Schmitt Trigger is used to digitize the conditioned signal. An open-collector output with current sinking capability provides the output signal. Protection against overvoltage and reverse polarity as well as against EMI are integrated and allow application in the hostile environments found in the automotive industry. VS 1 Protection Device Internal Reference and Supply Vreg (3V) Hall-Probes HighpassFilter SchmittTrigger Open Collector Protection Device Amplifier 2 Q 3 GND 4 CF AEB01695 Figure 60 Block Diagram TLE 4921-3U Data Book 32 2000-07-01 Silicon Hall ICs Method of Operation The generation and evaluation of the difference signal can be explained with reference to a typical application such as sensing a ferromagnetic gear wheel. Gear Wheel Hall Probe 1 Hall Probe 2 Signal Processing Circuitry S (N) N (S) Permanent Magnet Output Signal Magnet Wheel S N Hall Probe 1 S Hall Probe 2 Signal Processing Circuitry AEA01590 Figure 61 Application as a Gear Wheel Sensor and as an Encoder Wheel Sensor Data Book 33 2000-07-01 Silicon Hall ICs A permanent magnet mounted with either pole on the rear side of the IC produces a constant magnetic bias field. The two Hall probes are spaced at 2.5 mm. If one cell faces momentarily a tooth while the other faces a gap of the toothed wheel, the gear tooth acts as a flux concentrator. It increases the flux density through the Hall probe and a differential signal is produced. As the toothed gear wheel turns, the differential signal changes its polarity at the same rate of change as from the tooth to the gap. The maximum difference is produced by the tooth edge when the zero crossover comes directly in the center of the tooth or gap. When the difference exceeds the upper threshold BRP, the output transistor of the TLE 4921-3U will turn OFF (VQ = HIGH).This is the case when the tooth is sensed by the Hall probe 2 near pin 4 in Figure 61. As the difference falls below the lower threshold BOP, the transistor turns ON (VQ = LOW). This is the case when the Hall probe 1 near pin 1 senses the tooth. The integrated highpass filter regulates the difference signal to zero by means of a time constant that can be set with an external capacitor. In this way only those differences are evaluated that change at a minimum rate (depending on the capacitor value). The output signal is not defined in the steady state. The accuracy that is produced will permit a small switching hysteresis and therefore also a large airgap (up to 3.5 mm). Data Book 34 2000-07-01 Silicon Hall ICs N (S) S (N) 1 B1 Wheel Profile B2 Missing Tooth 4 Magnetic Field Difference B = B2-B1 Small Airgap Large Airgap B RP = 0.75 mT B HYS B OP = -0.75 mT Output Signal VQ Operate point : B2 - B1 < B OP switches the output ON (VQ = LOW) Release point : B2 - B1 > B RP switches the output OFF (VQ = HIGH) B RP = BOP + B HYS The magnetic field is defined as positive if the south pole of the magnet shows towards the rear side of the IC housing. AED01697 Figure 62 Sensor Signals Produced by a Toothed Gear Wheel Data Book 35 2000-07-01 Silicon Hall ICs Gear Wheel, Sensing Distance and Angular Accuracy A gear wheel is characterized by its modulus: d: pitch diameter z: number of teeth The space T from tooth to tooth, the pitch, is calculated by the formula T = m d m = -z T Conversion DIN - ASA d AEA01260 m = 25.4 mm/p T = 25.4 mm CP DIN ASA diameter (mm) number of teeth module m = d/z (mm) pitch T = x m (mm) d z m T p PD CP diameter pitch p circular pitch = z/d (inch) pitch diameter PD = z/p (inch) CP = 1 inch x /p Figure 63 Toothed Wheel Dimensions The difference in induction is at its greatest when one Hall element faces a tooth and the other one a gap. The spacing between the Hall elements on the IC is 2.5 mm, so the IC can detect a difference from the modulus 1 upwards, the corresponding pitch being 3.14 mm. If the modulus is much greater than 3, or the wheels are irregular, there is a risk of insufficient difference in induction over a longer period, meaning that the output signal will be nondefined. The maximum possible distance between the sensor and the gear wheel - as a function of temperature, the modulus, the magnet and the speed - will be characterized by the fact that just one impulse manages to appear at the output for each tooth/gap transition. The following measurements are made with different magnet types: Table 14 Magnetic Type Size (in mm) SmCo5 5 x 4 x 2.5 Sm2Co17 6x3x5 300 NdFeB o5x3 280 NdFeB o 7.9 x 2 230 B at d = 0.5 mm (in mT) 250 Data Book 36 2000-07-01 Silicon Hall ICs 3.5 mm 3.0 2.5 AED02078 Airgap 2.0 1.5 1.0 0.5 0.0 Sm 2Co17 SmCo5 NdFeB 7, 9*2 NdFeB 5*3 -50 0 50 100 150 C 200 TA Figure 64 Maximum Sensing Distance for a Gear Wheel with Modulus 1,5 as a Function of Biasing Magnet If the distance is reduced, a larger useful signal is produced. Therefore the switching accuracy increases with which a Low/High transition of the sensor can represent an angle of rotation of the gear wheel. Filter Capacitor The filter capacitor CF plays an important role in the correct function of the Hall IC. If an application requires operating temperatures higher than 100 C, ceramic capacitor types (X7R) are recommended. The connections between the filter capacitor CF, the C pin and the GND pin need to be as short as possible. Further recommendations are listed in one of the following subsections. A leakage current at the capacitor pin will cause a shift of the switching thresholds and therefore spurious switching. The shift of the switching threshold is calculated as I L x RC ( T ) B m = --------------------------SC( T ) where IL, SC and RC are the leakage current, the filter sensitivity to B and the filter input resistance as specified in the datasheet respectively. Special attention has to be paid to the choice of the capacitor (high DC resistance) and its assembly. Leakage currents may occur on the PCB between the connections or in a defective capacitor and can be a source of sensor malfunction. Data Book 37 2000-07-01 Silicon Hall ICs EMC: Injection of supply line transients (DIN 40839-1 and -2) For the measurements with the TLE 4921-3U the test circuit shown in Figure 65 is used. The filter capacitor CF = 470 nF is connected directly to pin 4, additionally a shunt capacitor CS = 4.7 nF is placed in the supply line. A serial resistance of 300 is used (400 for test pulse 5). Some applications do not allow such a high serial resistance, because it causes an undesired supply voltage drop. With a smaller serial resistance in the range of 50 - 150 the following results are almost not affected, except the ones of pulse 5. Due to its long duration up to 400 ms this so-called load dump pulse generates high power levels to be dissipated in the Hall IC. Without a sufficiently large serial resistor the IC would be destroyed. Therefore the minimum resistor size must be adapted to the load dump requirements of the application or vice versa. Optionally a suppressor diode can be placed in the supply line, eliminating the need for a large serial resistor. RS 1 VS 300 (Pulse 5 : 400 ) VS = 12/24 V (13.5/27 V) RL 2 k VOUT CS 4.7 nF CF 470 nF 4 2 TLE C 4921-3U Q GND 3 GND AES02060 Figure 65 Circuitry for DIN 40839-1/-2 Test The results obtained with the TLE 4921-3U are summarized in Table 15. The values in parenthesis apply for 24 V battery voltage operation. Detailed results of the measurements are available on request. Data Book 38 2000-07-01 Silicon Hall ICs Table 15 Functional Status of TLE 4921-3U according to DIN 40839-1/-2 Test Levels Test Pulse I 1 2 3a 3b 4 5 6 7 C (C) A (A) C (C) A (A) C (C) B (C) C C Functional Status according to Test Levels II C (C) B (B) C (C) A (C) C (C) C (C) C C III C (C) B (B) C (C) C (C) C (C) C (C) C C IV C (C) B (B) C (C) C (C) C (C) C (C/D) C C D: if t0 > 200 ms A/B: if t2 = 60 s EMC: Radiated Interference (DIN 40839-4) This test is carried out in a TEM cell. The setup is described in Chapter 6.4 (Electromagnetic Compatibility in Automotive Application). The PC-board, onto which the sensor is mounted, is optimized according the circuit in the following subsection. The results of the TEM measurements with an optimized PCB board are shown in Figure 66. It is seen that over the whole frequency range the TLE 4921-3U performs without disturbance up to the maximum field of 160 V/m. More details on the TEM measurements are available on request. Data Book 39 2000-07-01 Silicon Hall ICs Figure 66 Results of the Radiated Interference Test with the TLE 4921-3U Data Book 40 2000-07-01 Silicon Hall ICs Optimization of TLE 4921-3U PCB Layout for Improved EMI Performance, Threewire Configuration Due consideration of the PC-board layout is a prerequisite for optimized EMI performance of the TLE 4921-3U. The following recommendation is the result of EMI measurements carried out on the device during in-house testing. Figure 67 Optimized TLE 4921-3U PCB Circuit for Three-wire Operation Component values: CF = 470 nF CS = 4.7 nF Rp = 0 - 330 Cp = 4.7 nF Rq = 33 Cq = 4.7 nF RL = 330 High pass filter capacitor Additional HF shunt (optional) Forms with Cp a low pass filter in the supply line (against conductive coupling and fast interference pulses) Serves with Cq to smoothen the falling edge of VSIGNAL, i.e. reduction of irradiated interference Load resistor Data Book 41 2000-07-01 Silicon Hall ICs Optimization points in detail: 1. Ground The reference point on the board is the GND pin of the device. In order to avoid conductive interferences, all connections to this pin should be realized in a star configuration. If this requirement is not fulfilled, the EM immunity will be reduced. 2. Connection of the filter capacitor The connections between the filter capacitor CF, the C and GND pins have to be as short as possible (ideally CF should be placed close to the device housing), taking into account the above mentioned star configuration of CF to GND. If this is not possible, a second smaller capacitor (e.g. 82 nF) between CF and TLE 4921-3U is recommended in order to shorten the connection between CF and the corresponding pins. This measure should be applied only if little space is available close to the Hall IC. 3. Groundscreen In addition it is recommended to lay the GND connection of the filter capacitor out as a groundscreen for the connection of the capacitor to the C pin. 4. Additional RF shunts Ideally arranged RF shunts CS can further improve the EMI immunity. The effect of the above listed optimization steps (with decreasing significance) can vary according to the system (sensor, cable, control unit). Depending on the application, not all the measures need to be applied. Detecting Speed of Rotation The output signal of the gear-tooth-sensor is rectangular. Each alteration of the switching status represents a change from tooth to gap or vice versa. The duty cycle for a rectangular tooth-wheel (e.g. modulus 2) and sensing distance of 1 to 2 mm is virtually 1:1. Depending on the application the speed information will be required in digital form or in analog form as a voltage. Analog Evaluation Speed control is the commonest task in classic control engineering. The controlled variable that is taken for an analog controller (P, PI, PID) is a voltage proportional to the speed. The first step in obtaining this speed proportional voltage is that the sensor output signal is converted into a rectangular signal fixed ON-time and a variable OFF-time, dependent on the speed, by an edge-triggered monoflop. In the second step the linear average is formed. This, using a conversion factor, is directly proportional to the speed. Data Book 42 2000-07-01 Silicon Hall ICs Vanalog = Vop x RC x T/60 x rpm Operating voltage Set monoflop time Revolutions per minute No. of teeth on wheel A moving-coil meter is especially suitable for analog display of the speed. This is an ideal averager above a lower cut-off frequency of typically 10 Hz. If the speed-proportional voltage is processed electrically, the average value can be formed by a lowpass filter. Digital Evaluation If the speed-proportional voltage is to be produced as a digital, numeric reading, or if there is a microcomputer available in the system as a digital controller, the speed can be computed very easily for these purposes. The gear-wheel sensor is connected to the count input of a microcontroller (e.g. external input of timer 0 on an 8051). The speed is detected by counting the HIGH/LOW transitions of the sensor output in a defined time window Twindow. By careful definition of this time window, the speed can be produced directly as an rpm figure without conversion. Counted pulses Speed [ rpm ] = ---------------------------------------60 with T window [ s ] = -----------------------------------------Number of teeth T window Example: A gear wheel with 15 teeth requires a time window of 4 s. If one pulse is counted in the time window, this will correspond to 1 rpm. This is at the same time the finest resolution that is possible. Because of the high operating frequency of the microcontroller however, it is bothersome to set long time windows. If you select a shorter time window, the count has to be multiplied by a correction factor in the ratio of the ideal to the real time window. The metering accuracy and resolution that are achieved can nevertheless only amount to this factor at the maximum. Example: Gear wheel with 15 teeth time window 4 s. Real time window 40 ms correction factor 100. If one pulse is counted in the set time window, this will correspond to 100 rpm. If none is counted, the display will be zero. It is seen that the lower metering limit is determined by the choice of time window. Data Book 43 2000-07-01 Silicon Hall ICs Detecting Sense of Rotation With Logic Detecting the sense of rotation is a very simple matter with two sensors. These sensors should be arranged on the circumference of the tooth wheel so that their output signals are offset 90 in phase. The switching sequence of the sensors is converted into a static directional signal by an edge-triggered D-flipflop, because one sensor will switch earlier than the other depending on the sense of rotation. The output signal of the dynamic tooth-wheel sensor is only valid above a minimum speed, this also applying to the direction signal that is obtained. So when a gear wheel is braked and started again in the opposite direction, the output signals and the direction signal about the standstill point are not particularly reliable. With Software The switching sequence can also be evaluated by a microcontroller and software. The sensor signals are connected to two interrupt inputs. At the same time it is possible to monitor the lower cut-off frequency by software. The sensor signals are not evaluated if they go beyond the lower cut-off frequency. The principle of detecting sense of rotation is illustred in Figure 68. A proven application circuit for analog sensing of rotational speed and sense is shown in Figure 69. Data Book 44 2000-07-01 Silicon Hall ICs Figure 68 Detecting Sense of Rotation with Two Gear-Wheel Sensors Data Book 45 2000-07-01 Silicon Hall ICs Figure 69 Application Circuit Rotational Speed/Rotational Sense Data Book 46 2000-07-01 Silicon Hall ICs Signal Behaviour for different Dimensions of Toothed Gear Wheels In order to give detailed information regarding to the signal behaviour for different gear tooth dimensions, the main points that influence the performance of a sensor/toothed wheel configuration are described below. The following figures show the internal differential signal coming from two Hall elements, receiving a direct information on how the dimensions influence the performance. The differential signal increases with the ferromagnetic mass and therefore with the tooth pitch T. If T is increased to more than 8 mm, the gradient becomes flat. Hence the optimum rating is then between 5 and 8 mm (Figure 70). Figure 70 Differential Signal as a Function of Pitch T According to the definition the position dv = 0 mm is where the tooth of the wheel is centered over the IC. Therefore at this position the differential signal is 0 (both Hall elements are influenced by the same magnetic flux). At the position where one Hall element faces a gap and the second element faces a tooth, the differential field has a maximum (dv = 1.25 mm). If T equals 5 mm then the differential signal is sinusoidal because the distance between the sensors is 2.5 mm = T/2 (see Figure 71). Data Book 47 2000-07-01 Silicon Hall ICs Figure 71 Differential Signal for a Pitch T = 5 mm If T/2 is smaller than 2.5 mm, the influence of the gaps decreases and the Hall elements already detect the next tooth (Figure 72). Figure 72 Differential Signal for a Pitch T = 3 mm Data Book 48 2000-07-01 Silicon Hall ICs If T/2 is larger than 2.5 mm, the influence of the gaps increases and the Hall elements do not detect the next tooth (Figure 73). Figure 73 Differential Signal for a Pitch T = 8 mm Figure 74 shows the influence of slanted teeth. Figure 74 Differential Signal for Teeth with Different Slant Data Book 49 2000-07-01 Silicon Hall ICs The differential signal for different tooth height Zh for T = 5 mm is shown in Figure 75. Zh equal to 5 mm already produces a large amplitude. A further increasing of Zh only leads to small improvements. Figure 75 Differential Signal as a Function of Tooth Height, T = 5 mm Of special interest, together with the influence of tooth geometry, is the signal behaviour of the sensor for varying airgaps dA. in Figure 76 the differential signal of a toothed wheel with T = 4 mm and dv = 1 mm is shown as a function of the effective airgap. Figure 76 Differential Signal as a Function of Airgap dA for T = 4 mm and dv = 1 mm Data Book 50 2000-07-01 Silicon Hall ICs A summary of the discussed points is shown in Figure 77: Figure 77 Optimum Application Configuration for the Differential Sensors, Dimensions in mm Data Book 51 2000-07-01 |
Price & Availability of TLE4921-3U
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |